© 2011 by Harold Melton, KV5R. All Rights Reserved.
Shop for 2 Meter Antennas here.
Cost, you no longer need to buy a new antenna to get a 7 band G3TXQ Hexbeam, you just buy the kit. Ease of build, it only takes approx 1 hour to fit the 40m element to the 6 band G3TXQ Hexbeam. During the modelling of the 40m element I noted some significant points. These 'negatives' outweigh in our minds the simplicity, durability, and confirmed performance of the 2 element hex beam. So, at least for now, we don't plan to offer a 3 element hex beam. We believe the outstanding reputation of the conventional hex beam does not deserve the risk that would go along with the added size and complexity of 3. A homebrew Hexbeam antenna built in 3 hours. Qts1081b driver download. How to build your own HEX. You should join the Hex-beam. element formula. The Reflector is then made 4% larger. This page covers 3 element Yagi Antenna calculator. The formula and basics of Yagi Antenna Calculator are also explained with example. The calculators for other antenna types such as parabolic,horn,dipole and patch are also mentioned. What is Yagi Antenna? The simple Yagi Antenna is shown in the figure-1. It consists of three elements viz.
This antenna is similar in construction to the 2-meter OFC sleeve dipole I built over 8 years ago, but it is a simple center-fed dipole. I used 1″ thin-wall PVC pipe, aluminum tape, and RG-8X coax. https://trueqfile518.weebly.com/sketch-3-5-2.html. The goal here is to put up a cheap, easy, and quick 2-meter antenna that is simple and unobtrusive, but works quite well.
If you have the materials handy, you can build and install this antenna in a couple hours. Pagemaker 7 windows 10 download. This dipole was constructed as follows:
Cut 6 or 7 feet of 1″ thin-wall PVC.
A good way to adjust a Yagi antenna, is by facing the antenna straight up, so the reflector is parallel to the ground or in this case at an angle. At the back of the antenna,is a length of PVC pipe placed there to keep the antenna from spinning.
Cut two 38″ lengths of aluminum tape.
Put one edge of the first tape on the pipe, nice and straight.
Slide fingers along the tape, rotating the pipe slightly with each slide.
Try to make no wrinkles.
Apply the second tape, starting with about a 1/8th″ overlap.
Find the exact center of the tapes and cut away ¼″.
Cut 4 pieces of aluminum tape about 5 inches long. Wrap them
around the 4 ends of the two elements. The extra thickness at
the feed-point will handle more power than a single layer.
I used 16½ feet of RG-8X, which is 3 waves at 147MHz and VF .82.
Strip out 1½ inches of the coax like this.
Dip the conductors in synthetic grease to help avoid corrosion.
Use a high-quality tape like 33+, tightly wrap the conductors down against the pipe.
Be careful to not spread grease around while taping.
Tape down the shield, as tightly as you can stretch the tape.
Add a couple of small ties over the taped conductors. Pull them as tight as you can
without breaking them. This is to further mash the conductors into the elements.
Best Hex Beam Antenna
Now bring the coax down and add a couple of ties to it, as a strain-relief.
Now tape the whole connection. Start in the middle, half-lapping upwards, then
work down to the bottom, then back up to the middle. Note that you can't do this
with cheap vinyl tape — you need something that will stretch and seal.
Apply a tie-wrap to the tape's tail, so it won't unravel.
Now notice that you have these two little gaps, where the coax comes out.
Dab a little silicone caulk there to keep out spiders and moisture.
Thinwall PVC is too brittle to clamp it with a u-bolt. Cut a little piece of
sch-40, slit it, spread it, and slip it over the pipe for reinforcement.
Cut two 38″ lengths of aluminum tape.
Put one edge of the first tape on the pipe, nice and straight.
Slide fingers along the tape, rotating the pipe slightly with each slide.
Try to make no wrinkles.
Apply the second tape, starting with about a 1/8th″ overlap.
Find the exact center of the tapes and cut away ¼″.
Cut 4 pieces of aluminum tape about 5 inches long. Wrap them
around the 4 ends of the two elements. The extra thickness at
the feed-point will handle more power than a single layer.
I used 16½ feet of RG-8X, which is 3 waves at 147MHz and VF .82.
Strip out 1½ inches of the coax like this.
Dip the conductors in synthetic grease to help avoid corrosion.
Use a high-quality tape like 33+, tightly wrap the conductors down against the pipe.
Be careful to not spread grease around while taping.
Tape down the shield, as tightly as you can stretch the tape.
Add a couple of small ties over the taped conductors. Pull them as tight as you can
without breaking them. This is to further mash the conductors into the elements.
Best Hex Beam Antenna
Now bring the coax down and add a couple of ties to it, as a strain-relief.
Now tape the whole connection. Start in the middle, half-lapping upwards, then
work down to the bottom, then back up to the middle. Note that you can't do this
with cheap vinyl tape — you need something that will stretch and seal.
Apply a tie-wrap to the tape's tail, so it won't unravel.
Now notice that you have these two little gaps, where the coax comes out.
Dab a little silicone caulk there to keep out spiders and moisture.
Thinwall PVC is too brittle to clamp it with a u-bolt. Cut a little piece of
sch-40, slit it, spread it, and slip it over the pipe for reinforcement.
Mount it on something…
Run the coax in…
Install your favorite coax connector…
Hex Beam Antenna
and test it!
Notes
- You can protect the elements from corrosion with paint, or better, outdoor polyurethane varnish.
- If installing near a metal roof like I did, you'll need to find the right height above the metal before the SWR will come down. In my case, I ended up with it about ½-wave above the roof, then the SWR went nearly flat across the band. With it lower, as shown above, the SWR was around 2.
- For the elements, 38 inches (total, including the gap) should give you a low SWR across the band. If it doesn't, try changing the antenna's environment before altering the antenna.
- You can also adjust the SWR somewhat by changing the dangle-angle of the coax. In my case, it ended up being best about 1' from the lower element, while bringing it out perpendicular didn't work worth a darn! That's a lucky thing, I guess, since a perpendicular feed-line would side-load the PVC.
- If you wanna put it up on a metal pole, I'd suggest leaving ½-wave (about 40') of bare PVC between the lower element and the metal pole.
- Please feel free to drop me an email if you build one and let me know how it works or how it could be better!
So there you have it—I told you it was easy!
Build A Hex Beam Antenna
—73, KV5R
NVIS Army FM 24-18 — 2-Meter Sleeve Dipole
